BPY OSRAM Opto Semiconductors Phototransistors PHOTODIODE datasheet, inventory, & pricing. Osram Opto BPY available from 10 distributors. Explore Sensors on Octopart: the fastest source for datasheets, pricing, specs and availability. Osram Opto BPY available from 16 distributors. Explore Sensors on Octopart: the fastest source for datasheets, pricing, specs and availability.
|Published (Last):||25 October 2011|
|PDF File Size:||3.31 Mb|
|ePub File Size:||9.75 Mb|
|Price:||Free* [*Free Regsitration Required]|
BPY62 Datasheet PDF
On this project I have one problem. As the product is customised to your requirements, we cannot accept returns should you decide you no longer want the instrument. These four tracks would symbolize the 4-bit output A, B, C, D. Then I design the tracks on the Perspex 4 circular tracks around the Perspex. So I decided to make the encoder with brushes, instead of the opto-couplers. Introduction In collaboration with Intertek, Distrelec is offering a calibration service for new electronic test and measurement instruments.
Gpy62 this datassheet by email Print this page Report an error Report an error Thank you for helping us with our website! A description datahseet and identification eg. Image is for illustrative purposes datashret. Both the sender and receiver need to have a separate PCB. Only datahseet of its 16 outputs Y0 to Y15 will go low logic 0 for each of the 16 possible values of the 4-bit binary code on its inputs.
An error occurred login failed. An identification of the calibration method eg.
BPY60, BPY61, BPY62
A prevention that I made was that I added a heat sink with the regulator because the first time that I switch on the circuit, it became really hot. The circuit has taken about mA. My solution for this problem of the shaft encoder is that I can cut rounded transparent Perspex. You will find two items appearing, one version without a calibration service item-nr. Thank you for your message. Only private customers can order as guest.
This device involves a lot of mechanical pieces and electronics itself. All orders for calibrated items are non-cancellable and non-returnable. My project is about a wind vane that provides wind direction via a digital output utilizing an LED configuration.
Wavelength of Peak Sensitivity. Close Your message has been sent. When infrared has light on it, the phototransistor is low short circuit0. Our expert team have over 25 years experience solving problems and providing expert advice. The combinations were all displayed all after each other and not mixing the combinations.
Siemens BPY62 Series Datasheets. BPY62, BPY, BPY, BPY, BPY, BPY Datasheet.
This problem that I vpy62 attempting to solve is how to make the shaft encoder from gray code to binary for the vane. Reduce paperwork and access all invoices in one place using My Account. Can Bppy62 return the calibrated item if I am not satisfied with the device itself? Electronic Wind Vane This project is about a wind vane that provides wind direction via a digital output utilizing an LED configuration.
Usually the time for the calibration of your device can be handled within 5 working days. Collector-Emitter Saturation Voltage Max. The measured values detected by the calibration Calibration in a controlled environment measuring laboratory. The emitters and transmitters developed this excess of current because they were both of them in parallel.
I was fortunate to decide that I datasheef choose and adapter that a simple 9V battery. This additional time for the calibration should be taken into consideration to your normal delivery time.
In this stage it involves the opto-electronics part that is the datahseet encoder and that I encountered some difficulties. First, the infrared sender resistor must be about ohms, and the phototransistor pull-up resistor must be about 33k ohms. Expert technical support on hand Our expert team have over 25 years experience solving problems and providing datashedt advice. Environmental information RoHS Conform. How to get the instrument calibrated?
If the detected deviation is too large in relation to factory specification, adjustment of your data logger or measuring instrument will be required. At the beginning it was difficult to find a pair of opto couplers from the shops because they were out of stock. Send to a friend. Products The range of this service include, but not limited to: So this would involve four infrared senders and four infrared receivers. The difficulties were encountered when I arrived in the part of the opto-couplers.