This standard is issued under the fixed designation D ; the number immediately 1 This test method is under the jurisdiction of ASTM Committee D10 on. 11 Oct ASTM D Compressive Resistance of Shipping Containers and Unit Loads. Summary. This test method is used to evaluate the compressive. 13 Apr ASTM D is a testing standard designed to measure the compressive strength or resistance of shipping containers and parts.
|Published (Last):||6 September 2015|
|PDF File Size:||7.97 Mb|
|ePub File Size:||10.22 Mb|
|Price:||Free* [*Free Regsitration Required]|
We’re ready to help! Compressive resistance is one of the properties used to evaluate the ability of shipping containers, components, and unit loads to successfully survive the compressive forces they are subjected to during storage and distribution.
Speak with one of our fixture specialists to learn more about our compression platens. Test Procedure Select a sample size and condition each specimen as indicated Carefully center the specimen on the bottom compression platen Slowly bring the top platen into contact with the specimen Apply the desired pre-load Make sure your system is set to specimen deformation Begin to apply load at the constant rate indicated in the specification Continue test until failure or specified load Repeat this procedure with each specimen.
Testing packing components for compressive strength is needed to help guarantee the protection of the products inside them. The lower platen should be rigid, such as the G23 Compression Platen this platen is required for edge or corner testing.
Spherical platens can be used in face-to-face testing to allow the platen to change angles and stay in contact with the non-uniform crushing of a container. Give one of our engineers a call today and they can help guide you through the ASTM Asm test process with the best machine configuration for your requirements.
Our engineers recommend that you pair your compression test machine with an upper platen fit with a spherical bearing to ensure even distribution of load. Link to Active This link will always route to the current Active version of the standard. Contact our Engineers Today! Shipping containers may be tested with or without contents. Standard load ratings up to kN 67, lbf ; higher ratings available upon request Platen diameters atm 56 mm to mm 2. When you are ready to perform this test, please refer to and follow the exact specifications in the official ASTM D document.
Both platens need to be large enough to completely cover each end of the specimen. It is the responsibility of the user of this v642 to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Referenced Documents purchase separately The documents listed below d62 referenced within the subject standard but are not provided as part of the standard.
Fixed-platen machines generally cause corrugated aztm specimens to fail at their strongest point, while swivel-platen machines cause corrugated box specimens to fail at their weakest point. We offer machines, apparatus, testers, tensile grips, test fixtures, clamps, holders, jigs, faces, jaws, extensometers, environmental and d624 chambers, furnaces, baths and custom solutions for unique applications.
Automotive Interior Mechanical Testing Guide. Our engineers would recommend pairing your compression tester with Xy Software to allow the user to collect all force and displacement data points during the test.
Also, unit loads are generally tested only in the top-to-bottom orientation. ASTM D tests the compressive resistance of shipping containers including boxes and drums and components.
ASTM D642 Compressive Resistance Test Equipment for Shipping Containers, Components and Unit Loads
For constant load test refer to Test Method Atsm The ISO standards may not meet the requirements for this test method. Sales Support Calibration Calculators. The procedure may be used for measuring the ability of the container to resist external compressive loads applied to its faces, to diagonally opposite edges, or to corners Fig. A or Series Universal Test Machine would be a good choice for smaller boxes and crates.
Qstm D may be used for measuring the ability of the container to resist external compressive loads applied to its faces, to diagonally opposite edges, or to corners.
ASTM D Compressive Resistance Test Equipment for Shipping Containers, Components and Unit Loads
We are confident that we have what you are looking for. Standard load ratings up to kN 67, lbf ; higher ratings available upon request Platen diameters available from 56 mm to mm 2. Historical Version s – view previous versions of standard. Planar Biaxial Testing Guide. Your compression test machine choice will depend on the maximum specimen size that you need to test.
Packaging components such as boxes, crates, and cases are designed to protect wstm while they are transported and stored. How to Zstm a New Test.
Force range of 5 kN to kN 1, lbf tolbf Adjustable test space The most popular choice for static tension and compression tests These dual column testers are available in both tabletop and floor standing models.
The values given in parentheses are mathematical asttm to SI units that are provided for information only and are not considered standard. ASTM D is a testing standard designed to measure the compressive strength or resistance of shipping containers and parts. Fixed platens are rigidly mounted and can be used for corner testing, edge testing or face-to-face testing opposite sides of the box.
ASTM D can be used to test packaging diagonally along opposite edges or top to bottom. G Spherical Seat Compression Platens. The Series Universal Test Machine is a common choice for this d64, and specifically the Family are aatm for wide column spacing for large boxes, crates and pallets.
Have a question about conducting the test for this standard? However, a fixed-head compression machine is required to perform edge-to-edge and corner-to-corner orientations on test d64 see Note 2. D Terminology of Packaging and Distribution Environments.
The best platen choice would be the TestResources G with an upper bearing.
ASTM D Test Method for Determining Compressive Resistance of Shipping Containers
This test method covers testing of multiple containers or unit loads, in addition to individual shipping containers, components, materials, or combination thereof. Users can choose to test with fixed or spherical platens.
Specimens for ASTM D should be the full shipping container prepared in the same way that it will be used for packing and shipping. This is a general guide designed to help you understand the basic test procedure and equipment needed to test your products and materials to this standard. During distribution and warehousing, items are placed under various compressive loads while being stacked and moved. Our engineers are familiar with ASTM D and can help guide you through the testing process, but we recommend you purchase and read the official ASTM standard to achieve the best results.
You should make sure to test five or more atm and average the data to improve the statistical reliability of the data. We can create custom platens to your required specimen size.